企业官网建设流程全解析

一、RT-Thread-W25Q64-SPI配置

（一）SPI配置

1、创建工程后，打开设置，使能SPI

2、修改board.h头文件内容

3、打开stm32cube-使能对应SPI通道引脚（根据所使用的SPI通道进行设置）
W25Q64使用SPI2,相关设置如下所示：

4、生成代码，关闭stm32cubemx
修改stm32f4xx_hal_config_bak.h文件如框选所示，使能 SPI 外设模块的宏定义

5、将生成的SPI初始化函数复制到board.c文件末尾，原来文件中函数的内容注释掉

将复制的SPI初始化函数粘贴到board.c文件中末尾，如下图所示

随后将原来文件中的初始化函数注释掉

（二）读取W25Q64

SPI片选W25Q64芯片，挂载设备

struct rt_spi_device *spi_w25q64; //片选SPI和挂载W25Q64 void spi_init() { struct rt_spi_configuration cfg; //先把w25qxx挂载在SPI2总线上(pb12是W25Q的片选引脚) rt_hw_spi_device_attach("spi2", "spi20", GPIOB, GPIO_PIN_12); //查找设备 spi_w25q64=(struct rt_spi_device *)rt_device_find("spi20"); if(spi_w25q64==RT_NULL){ rt_kprintf("spi_w25q find failed...\n"); } else { rt_kprintf("spi_w25q find success...\n"); } //配置w25q-spi模式 cfg.data_width=8; cfg.mode=RT_SPI_MODE_3|RT_SPI_MASTER|RT_SPI_MSB;//模式3，主机，高位先行 cfg.max_hz=5*1000*1000;//5M rt_spi_configure(spi_w25q64, &cfg); //此时可以查看设备是否已注册 } MSH_CMD_EXPORT(spi_init,spi bus);

读取设备ID指令：0x90

方法一：

//读取id方法1 void spi_read_id1() { rt_uint8_t id[5]={0};// struct rt_spi_message msg1,msg2; rt_uint8_t w25_read_id=0x90;//读取ID指令 msg1.send_buf=&w25_read_id; msg1.recv_buf=RT_NULL; msg1.length=1; msg1.cs_take=1; msg1.cs_release=0; msg1.next=&msg2; msg2.send_buf=RT_NULL; msg2.recv_buf=id; msg2.length=5; msg2.cs_take=0; msg2.cs_release=1; msg2.next=RT_NULL; //制造商0XEF 设备IDxx rt_spi_transfer_message(spi_w25q64, &msg1); rt_kprintf("w25q128 ID is %x%x \n",id[3],id[4]); } MSH_CMD_EXPORT(spi_read_id1,spi_read_id);

方法二：

//读取id方法2 //先发送后接收数据函数 //rt_spi_send_then_recv(device, send_buf, send_length, recv_buf, recv_length) void spi_read_id2() { rt_uint8_t id[5]={0}; //存储id rt_uint8_t w25_read_id=0x90;//读取ID指令 rt_spi_send_then_recv(spi_w25q64, &w25_read_id, 1, id, 5); rt_kprintf("w25q128 ID is %x%x \n",id[3],id[4]); } MSH_CMD_EXPORT(spi_read_id2,spi_read_id);

完整代码如下所示

#include"rtthread.h" #include"rtdevice.h" #include"drv_spi.h" #include"drivers/spi.h" struct rt_spi_device *spi_w25q64; //片选SPI和挂载W25Q64 void spi_init() { struct rt_spi_configuration cfg; //先把w25qxx挂载在SPI2总线上(pb12是W25Q的片选引脚) rt_hw_spi_device_attach("spi2", "spi20", GPIOB, GPIO_PIN_12); //查找设备 spi_w25q64=(struct rt_spi_device *)rt_device_find("spi20"); if(spi_w25q64==RT_NULL){ rt_kprintf("spi_w25q find failed...\n"); } else { rt_kprintf("spi_w25q find success...\n"); } //配置w25q-spi模式 cfg.data_width=8; cfg.mode=RT_SPI_MODE_3|RT_SPI_MASTER|RT_SPI_MSB;//模式3，主机，高位先行 cfg.max_hz=5*1000*1000;//5M rt_spi_configure(spi_w25q64, &cfg); //此时可以查看设备是否已注册 } MSH_CMD_EXPORT(spi_init,spi bus); //读取id方法1 void spi_read_id1() { rt_uint8_t id[5]={0};// struct rt_spi_message msg1,msg2; rt_uint8_t w25_read_id=0x90;//读取ID指令 msg1.send_buf=&w25_read_id; msg1.recv_buf=RT_NULL; msg1.length=1; msg1.cs_take=1; msg1.cs_release=0; msg1.next=&msg2; msg2.send_buf=RT_NULL; msg2.recv_buf=id; msg2.length=5; msg2.cs_take=0; msg2.cs_release=1; msg2.next=RT_NULL; //制造商0XEF 设备IDxx rt_spi_transfer_message(spi_w25q64, &msg1); rt_kprintf("w25q128 ID is %x%x \n",id[3],id[4]); } MSH_CMD_EXPORT(spi_read_id1,spi_read_id); //读取id方法2 //先发送后接收数据函数 //rt_spi_send_then_recv(device, send_buf, send_length, recv_buf, recv_length) void spi_read_id2() { rt_uint8_t id[5]={0}; //存储id rt_uint8_t w25_read_id=0x90;//读取ID指令 rt_spi_send_then_recv(spi_w25q64, &w25_read_id, 1, id, 5); rt_kprintf("w25q128 ID is %x%x \n",id[3],id[4]); } MSH_CMD_EXPORT(spi_read_id2,spi_read_id);

编译运行结果

二、W25Q64+SFUD

（一）增加SFUD配置

在第一章节（一）SPI配置基础上增加

（二）编写代码

SPI片选，SFUD探测初始化

int w25q_sfud_test() { //片选挂载设备 // rt_hw_spi_device_attach(bus_name, device_name, cs_gpiox, cs_gpio_pin) rt_hw_spi_device_attach("spi2", "spi20", GPIOB, GPIO_PIN_12); //探测设备 // rt_sfud_flash_probe(spi_flash_dev_name, spi_dev_name) //使用sfud探测spi20设备，并将spi20连接的flash初始化为块设备，名称w25q128 if(rt_sfud_flash_probe("W25Q64", "spi20")==RT_NULL) { rt_kprintf("w25q64 prob failed...\n"); return -RT_ERROR; } return RT_EOK; } MSH_CMD_EXPORT(w25q_sfud_test,sfub test);

写入数据和读取数据测试

sfud_flash_t test_sfud; int w25q_read_write_test() { const uint8_t test_data[]="this is w25q sfud test data!"; uint8_t read_data[50]={0}; //获取设备句柄 /* * 使用 rt_sfud_flash_find 或者 rt_sfud_flash_find_by_dev_name 获取设备句柄： */ //test_sfud=rt_sfud_flash_find("spi20"); test_sfud=rt_sfud_flash_find_by_dev_name("W25Q64"); if(test_sfud==RT_NULL) { rt_kprintf("find sufd_flash failed...\n"); return -RT_ERROR; } else { rt_kprintf("find sufd_flash success...\n"); } //调用API进行读写操作 //写flash rt_kprintf("write flash...\n"); // sfud_write(flash, addr, size, data) // sfud_erase_write(flash, addr, size, data) // sfud_write(test_sfud, 13, sizeof(test_data), test_data); sfud_erase_write(test_sfud, 13, sizeof(test_data), test_data); //读flash rt_kprintf("read flash...\n"); sfud_read(test_sfud, 13, sizeof(test_data), read_data); rt_kprintf("read data:%s...\n",read_data); } MSH_CMD_EXPORT(w25q_read_write_test,sfub read write test);